Refrigerator ice water hookup
An ice maker is a great addition to any kitchen and can be simple to install with the right materials. Attach copper tubing to your cold water pipe to create a dedicated cold water line for your new appliance. Run this line to the back of your refrigerator or under-counter ice maker and secure it with a compression joint. Be careful during the installation process to prevent water damage, contact with electric wiring, or damage to other plumbing. This article was co-authored by our trained team of editors and researchers who validated it for accuracy and comprehensiveness.
An ice maker is a great addition to any kitchen and can be simple to install with the right materials. Attach copper tubing to your cold water pipe to create a dedicated cold water line for your new appliance. Run this line to the back of your refrigerator or under-counter ice maker and secure it with a compression joint.
Be careful during the installation process to prevent water damage, contact with electric wiring, or damage to other plumbing. This article was co-authored by our trained team of editors and researchers who validated it for accuracy and comprehensiveness. Together, they cited information from 14 references. Ice Makers.
Learn more. Learn more Method 1. Locate the closest cold water source. To install an ice maker you will have to tap into the closest-located cold water pipe. Find this cold water source, which may be found under a sink, below the floor, or in a wall. If you need to drill through the floor or wall to reach the pipe, it is best to hire a professional who will know how to avoid wires, ducts, or other plumbing.
You will need to install a cold water line for either a refrigerator ice maker or an under-counter ice maker. Shut off the water and drain the pipe. Turn off the main water valve before starting your project by turning it clockwise. This valve will likely be located on a perimeter wall of your home, in your basement, or near an outdoor water meter.
Open the cold water faucet to let water drain out of the pipe. Attach a saddle valve to a clean spot on the cold water pipe. A saddle valve is a valve that hugs a water line on both sides and supplies a low pressure stream from it. Wipe the area of your cold water pipe that you will attach the valve onto with a clean, wet cloth. Place a saddle valve onto the pipe and tighten its clamps so that it grips the pipe.
Screw the valve in to pierce a hole in the pipe. Slowly turn the handle of the valve in a clockwise direction. When you meet resistance, keep turning the valve firmly. Continue until the needle pierces through the pipe. Attach 0. Place 1 end of your copper tubing into the valve opening. Screw on a small compression joint to secure the connection.
Measure the distance between your ice maker and the cold water pipe before purchasing the copper tubing to get the appropriate length. Turn the water back on. Once you have attached the saddle valve and copper piping, you can turn your water back on. First, make sure all of your connections are secure. Turn the main water valve counterclockwise to turn the water back on. Open the saddle valve to rinse through the copper piping into a large bucket.
Gently turn the handle on your saddle valve counter-clockwise to open the valve. Direct the end of your copper tubing unto a large bucket. Let enough water flow through to fill the bucket, then close the valve. Method 2. Locate the ice maker on your refrigerator. If you are hooking up a refrigerator ice maker, find where it is located on the appliance. If you have a model of refrigerator that is 10 years old or older, the ice maker, including the part that hooks up to the copper tubing, is likely to be located in the freezer.
If you have a newer model, it may be located in the refrigerator door. Run the tubing to your refrigerator. Pull your fridge out to access the back of it. Depending on where you accessed your cold water pipe, carefully run the water line towards the back of your fridge. Avoid leaving the tubing somewhere it might get damaged, stepped on, or crushed. Try to run it flush against the bottom of your walls or cabinets where it is most likely to be safe. Use a compression fitting to attach the piping to the ice maker.
Compression fittings are fittings comprised of an outer nut and inner ring that join 2 pipes together. Ice makers will often come with the appropriate compression fitting for the cold water outlet. Follow the instructions on your manual to attach the piping properly, as refrigerator and ice maker models vary. Use nylon cable clamps to attach the tubing to your fridge. Avoid leaving the copper tubing hanging behind your fridge. Clip it firmly to the side of the fridge using 0.
Use a screwdriver to secure the clamps with standard No. Method 3. Measure the space you have available to install the ice maker. Using a tape measure, find out the height, length, and width of the space you have chosen to install your ice maker. This will help you narrow down what model of ice maker to purchase. An ice maker would be well-located under your kitchen cabinet to the side of your sink or refrigerator.
Choose an ice maker that best fits your needs. Under-counter ice makers are available in a large range of sizes with different production and storage capacities. Smaller models generally yield less ice and are less expensive. Shop for a model of ice maker with a drain pump. A drain pump is a pump that pulls waste water away from different sources, including ice makers, and brings it to a kitchen drain. Most models of ice maker come with a drain pump installed, which makes the installation of an extra, gravity drain unnecessary.
Invest a bit more money in your ice maker to make sure it has a drain pump installed, which will ensure that it functions better, requires less installation work, and is less likely to leak. Attach the ice maker to your cold water line with a compression fitting. Run your cold water line from the pipe to the back of your under counter ice maker. Gently insert the copper piping into the fixture on your ice maker. Carefully tighten the compression fitting to secure the connection.
To make this connection simple, drill dime-sized holes into the sides of your cupboard with an electric drill to easily thread the copper tubing through it. Wear safety goggles and gloves to protect your eyes and hands from any wood particles that may fly into the air while you do this. Put the ice maker into its place under the counter. Under-counter ice makers are typically very heavy, so have a friend or family member help you move it if necessary.
Once the cold water line is attached, lift the ice maker and gently fit it into its designated spot. As you move the ice maker, be sure to slowly pull the piping out through the holes in the sides of your cupboard to keep it from getting stuck under the machine. Include your email address to get a message when this question is answered. Already answered Not a question Bad question Other. Article Info This article was co-authored by our trained team of editors and researchers who validated it for accuracy and comprehensiveness.
This article will show you how to run a refrigerator water line for an ice maker and water dispenser. The story and how-to photos cover the project. Running a water line to a refrigerator to supply its ice maker and drinking water dispenser has never been easier. At one time, this was typically.
Fulfillment by Amazon FBA is a service we offer sellers that lets them store their products in Amazon's fulfillment centers, and we directly pack, ship, and provide customer service for these products. Something we hope you'll especially enjoy: If you're a seller, Fulfillment by Amazon can help you grow your business. Learn more about the program. Please make sure that you are posting in the form of a question.
A refrigerator water valve is an important component of most refrigerators that have an icemaker, water dispenser, or both.
Here is a step-by-step water line installation refrigerator guide. A new refrigerator with a water dispenser and ice maker needs to be hooked up to a COLD water line.
KitchenAid Refrigerator Water Line Installation Kit
Angie's List Answers is the trusted spot to ask home improvement and health questions and get answers from service companies, health providers and consumers. For ratings and reviews on companies in your area, search Angie's List. Hello, we just purchased a whirlpool refrigerator with a built water filtration system and ice maker Would I contact a plumber to install the water lead? Also, what would the approximate cost be? Make sure you do not have a small-diameter copper or plastic tube coiled up somewhere behind the reefer or in the back of an adjacent cabinet - they are frequently run during constrution, just not hooked up under the sink.
Anyone else NOT use their icemaker?
Skip to main content. Fridge Water Line. In Stock. I bought a new fridge and while sliding it out, the copper water line broke. With no desire to replace it with more copper, I purchased this. The whole process took under ten minutes. No mess, no leaks, no problems. It does arrive in a coil and will want to retain that shape when you first get it.
Sign-in or Register. All Departments All Departments. Your question was published, help is on its way!
No Ice - Refrigerator
Running a water line to a refrigerator to supply its ice maker and drinking water dispenser has never been easier. In most cases, the water line can be run from a kitchen faucet water supply line through the kitchen cabinets and over to the refrigerator. If running the line through the cabinets is not feasible, you might need to run a line through the floor and up to where the refrigerator is located. Flex water supply tubes are available in either a tough plastic nylon mesh or braided steel. Although the braided steel is considerably more expensive, the extra strength it provides is well worth the investment. It can be very inconvenient to move a refrigerator to get at a water line that has failed, so buy the best-quality water supply tube you can. If so, your job is very easy. Turn the water supply valve on and check for leaks. Tighten the fittings as needed, using channel-type pliers or an adjustable wrench. If you don't have a convenient water supply pipe and valve near the refrigerator, you must instead find another spot to hook up the water line. Usually, this will be at some other existing water hookup point, like the water supply lines connected to your sink faucet or dishwasher.
Connect and install the water line to your refrigerator
A fellow human who loves his planet and beyond, with interests that match and never end. One life. One love. Appreciate everything. When hooking up a water line to a fridge ice maker or a door water supply, you want to use the correct materials to ensure the water flows well and everything is hooked up correctly with minimal chance of leaks. Many refrigerators these days supply a source for drinking water inside or on the door and will make ice cubes for you.
How to Hook Up a Water Line to a Refrigerator From the Sink
Many new refrigerators now come equipped with water dispensers and ice makers. Installing a water line to your new refrigerator requires a little know how of the plumbing within your home. Proper installation is key to preventing leaks down the road. Len The Plumber offers ice maker line installation to your refrigerator and can have it done the same day. Our expert Maryland, Washington, and Northern Virginia plumbers can hook up your water line in no time.
How to Install a Water Line for a Refrigerator
I just got to wondering whether I'm the only holdout left who doesn't hook up the refrigerator icemaker. Many, many years ago, we got our first refrigerator with icemaker, and the ice was terrible tastingsomething about the frost-free affecting the taste, I was told. So when we got our next refrigerator, with icemaker, we just never hooked it up. When we do, we dont plan to hook up the icemakernot because we think the ice will taste bad, but because it seems to be the 1 cause of repairs for refrigerators and we don't want the bother or expense. So, much like people who decide not to have a DW and don't miss it, we figure we won't miss what we've never had. I do have a related question: Is it possible to remove the icemaker from the freezer portion of the refrigerator and reclaim that area for storage in the freezer?
Sub-Zero and Wolf International
A refrigerator with an automated ice maker and a built-in water dispenser does absolutely nothing if you do not have a water line to connect to it. You can solve this with an ice maker installation kit that allows you to use the plumbing beneath the sink. The kit provides you with the required parts to hook up a water line to your refrigerator. Find your water supply lines beneath your sink. You may have three water supply lines beneath the sink; two lines connect directly to the faucet while the third line connects to the dishwasher. The valve connected to the right side of the faucet is the cold water supply line.
Skip to main content. Icemaker Water Lines Refine Results. Browse Related Browse Related. Also shop in Also shop in. Frigidaire by Electrolux.How to Connect an Ice Maker - Cheap & Easy